The use of thermography as a nondestructive evaluation technique is increasingly popular for maintaining concrete structures. Most inspections merely evaluate the locations and shapes of defects on surfaces. To address this shortcoming, it proposes an inspection method and preventive work using a coating-type resin sensor combined with an infrared camera. No method has been developed to assess the depth of defects. In this approach, infrared-reactive resin is applied. Thermographic images of the target area are captured sequentially. Temperature curves obtained at each pixel during the cooling process are analyzed using Fourier transform to differentiate defect states in various parts of the temperature distribution. The temperature change is found to be correlated with the defect size. Approximately 5% aluminum powder is mixed into the applied gel resin. Because of its specific gravity, it tends to concentrate in areas damaged by compression failure or to float. This report discusses technologies related to identification of defects and measuring their size in infrared-reactive resin, with examination of the effectiveness of measures to prevent scattering and collapse of defects caused by structural degradation. A concentric loading test on reinforced concrete columns confined by gel resin ties is described herein. Test variables include concrete compressive strength of 232–244 N/mm2, both below and above the equipment hole that caused the defect, and to measure the relation, a comparison with test specimens that are free of defects.
| Published in | American Journal of Remote Sensing (Volume 12, Issue 1) |
| DOI | 10.11648/j.ajrs.20241201.14 |
| Page(s) | 24-32 |
| Creative Commons |
This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited. |
| Copyright |
Copyright © The Author(s), 2024. Published by Science Publishing Group |
Health Monitoring, Infrared Thermography, Non-Destructive Inspection, Reinforcement, Spalling Prediction
| [1] |
Ministry of Land, Infrastructure, & Transport. Infrastructure maintenance information. Available from <
https://www.mlit.go.jp/sogoseisaku/maintenance/02research/02_01_01.html > (accessed on 10 October, 2020). (in Japanese). |
| [2] | Nobuhiro Shimoi, Yu Yamauch, Kazuhisa Nakasho,“Preventive Work and Health Monitoring for Technology by Cracks of Concrete Surface Using Coating Type Resin Sensor”, International Journal of Sensors and Sensor Networks. Vol. 11, No. 1, 2023, pp. 1-10. |
| [3] | Matsuoka, H., Hirose, Y., Kurahashi, T., Murakami, Y., Toyama, S., Ikeda, H., Iyama, T. & Ihara, I. (2018) Application of a joint variable method for high accurate numerical evaluation of defect based on hammering test. Journal of the Society of Materials Science, Vol. 67, No. 9, pp. 869-876. (in Japanese). |
| [4] | Shimoi, N., Nishida, T., Obata, A., Nakasho, K., Madokoro, H. & Cuadra, C. (2016) Comparison of displacement measurements in exposed type column base using piezoelectric dynamic sensors and static sensors. American Journal of Remote Sensing, Vol. 4, No. 5, pp. 23-32. (in Japanese). |
| [5] | Ueda, H., Ushijima, S. & Shyutto, K. (2007) Properties and deterioration prediction of acid attacked concrete. Japan Society of Civil Engineers, Vol. 63 No. 1, pp. 27-41 (in Japanese). |
| [6] | Tamai, H. (2003) Elasto Plastic Analysis Method for frame with exposed-type column base considering influence of variable axial force. Journal of Structural and Construction Engineering, Vol. 68, No. 571, pp. 127-135. (in Japanese). |
| [7] | Miyashita, T., Ishii, H., Fujino, Y., Shoji, T. & Seki, M. (2007) Understanding of high-speed train induced local vibration of a railway steel bridge using laser measurement and its effect by train speed. Japan Society of Civil Engineering A, Vol. 63, No. 2, pp. 277-296 (in Japanese). |
| [8] | Michimura, K. (2008) Deterioration diagnosis technology by infrared method. Material Life Society, Vol. 20, No. 1, pp. 21-26 (in Japanese). |
| [9] | Hayashi, H., Hashimoto, K. & Akashi, Y. (2013) Improving detection accuracy of concrete damage by infrared thermography. Japan Concrete Institute, Vol. 35, No. 1, pp. 1813-1818 (in Japanese). |
| [10] | Shimizu, K. (1987) The latest technology for far-infrared use. Industrial Technology Association, pp. 6–24 (in Japanese). |
| [11] | Shimoi, N. (2001) The technology of personal mine detecting for humanitarian demining. SICE, Vol. 37, No. 6, pp. 577-583 (in Japanese). |
| [12] | Ono, K. (2003) Study on technology for extending the life of existing structures, New urban society technology fusion research. The Second New Urban Social Technology Seminar, pp. 11-23 (in Japanese). |
| [13] | Nakamura, M. (2002) Health monitoring of building structures. Society of Instrument and Control Engineers, Vol. 41, No. 11, pp. 819-824 (in Japanese). |
| [14] | Kumagai, K., Nakamura, H. & Kobayashi, H. (1999) Computer aided nondestructive evaluation method of welding residual stresses by removing reinforcement of weld. Transactions of the Japan Society of Mechanical Engineers, Series A, Vol. 65, No. 629, pp. 133-140 (in Japanese). |
| [15] | Hashizume, K., Hashimoto K., Matsuda Y. (2017) Inspection of bridges, tunnels, and pavements using visible light, infrared light, etc. Journal of Automotive Engineering (Measurement and Control), Vol. 56, No. 11, pp. 884-887. |
| [16] | Malgague, X. (2002) Introduction to NDT by active infrared thermography. Materials Evaluation, pp. 1-22. (in Japanese) |
| [17] | Xu, J., Wang, H., Duan., Y., He, Chen, S. & Zhang, Z. (2020) Terahertz imaging vibro-thermography for impact response in carbon fiber reinforced plastics. Infrared Physics & Technology, Vol. 109, pp. 1-7. |
APA Style
Shimoi, N., Yamauchi, Y., Nakasho, K. (2024). Infrared–Resin Crack Measurement and Preventive Work Technology for Maintenance. American Journal of Remote Sensing, 12(1), 24-32. https://doi.org/10.11648/j.ajrs.20241201.14
ACS Style
Shimoi, N.; Yamauchi, Y.; Nakasho, K. Infrared–Resin Crack Measurement and Preventive Work Technology for Maintenance. Am. J. Remote Sens. 2024, 12(1), 24-32. doi: 10.11648/j.ajrs.20241201.14
AMA Style
Shimoi N, Yamauchi Y, Nakasho K. Infrared–Resin Crack Measurement and Preventive Work Technology for Maintenance. Am J Remote Sens. 2024;12(1):24-32. doi: 10.11648/j.ajrs.20241201.14
Share This Article
Twitter
Linked In
Facebook
Copy
Download@article{10.11648/j.ajrs.20241201.14,
author = {Nobuhiro Shimoi and Yu Yamauchi and Kazuhisa Nakasho},
title = {Infrared–Resin Crack Measurement and Preventive Work Technology for Maintenance
},
journal = {American Journal of Remote Sensing},
volume = {12},
number = {1},
pages = {24-32},
doi = {10.11648/j.ajrs.20241201.14},
url = {https://doi.org/10.11648/j.ajrs.20241201.14},
eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ajrs.20241201.14},
abstract = {The use of thermography as a nondestructive evaluation technique is increasingly popular for maintaining concrete structures. Most inspections merely evaluate the locations and shapes of defects on surfaces. To address this shortcoming, it proposes an inspection method and preventive work using a coating-type resin sensor combined with an infrared camera. No method has been developed to assess the depth of defects. In this approach, infrared-reactive resin is applied. Thermographic images of the target area are captured sequentially. Temperature curves obtained at each pixel during the cooling process are analyzed using Fourier transform to differentiate defect states in various parts of the temperature distribution. The temperature change is found to be correlated with the defect size. Approximately 5% aluminum powder is mixed into the applied gel resin. Because of its specific gravity, it tends to concentrate in areas damaged by compression failure or to float. This report discusses technologies related to identification of defects and measuring their size in infrared-reactive resin, with examination of the effectiveness of measures to prevent scattering and collapse of defects caused by structural degradation. A concentric loading test on reinforced concrete columns confined by gel resin ties is described herein. Test variables include concrete compressive strength of 232–244 N/mm2, both below and above the equipment hole that caused the defect, and to measure the relation, a comparison with test specimens that are free of defects.
},
year = {2024}
}
TY - JOUR T1 - Infrared–Resin Crack Measurement and Preventive Work Technology for Maintenance AU - Nobuhiro Shimoi AU - Yu Yamauchi AU - Kazuhisa Nakasho Y1 - 2024/06/03 PY - 2024 N1 - https://doi.org/10.11648/j.ajrs.20241201.14 DO - 10.11648/j.ajrs.20241201.14 T2 - American Journal of Remote Sensing JF - American Journal of Remote Sensing JO - American Journal of Remote Sensing SP - 24 EP - 32 PB - Science Publishing Group SN - 2328-580X UR - https://doi.org/10.11648/j.ajrs.20241201.14 AB - The use of thermography as a nondestructive evaluation technique is increasingly popular for maintaining concrete structures. Most inspections merely evaluate the locations and shapes of defects on surfaces. To address this shortcoming, it proposes an inspection method and preventive work using a coating-type resin sensor combined with an infrared camera. No method has been developed to assess the depth of defects. In this approach, infrared-reactive resin is applied. Thermographic images of the target area are captured sequentially. Temperature curves obtained at each pixel during the cooling process are analyzed using Fourier transform to differentiate defect states in various parts of the temperature distribution. The temperature change is found to be correlated with the defect size. Approximately 5% aluminum powder is mixed into the applied gel resin. Because of its specific gravity, it tends to concentrate in areas damaged by compression failure or to float. This report discusses technologies related to identification of defects and measuring their size in infrared-reactive resin, with examination of the effectiveness of measures to prevent scattering and collapse of defects caused by structural degradation. A concentric loading test on reinforced concrete columns confined by gel resin ties is described herein. Test variables include concrete compressive strength of 232–244 N/mm2, both below and above the equipment hole that caused the defect, and to measure the relation, a comparison with test specimens that are free of defects. VL - 12 IS - 1 ER -
Faculty of Systems Science and Technology, Akita Prefectural University, Yurihonjo, Japan
Faculty of Systems Science and Technology, Akita Prefectural University, Yurihonjo, Japan
Graduate School of Sciences & Technology for Innovation, Yamaguchi University, Ube, Japan
Information
Email: