Ionic Polymer Metal Composites (IPMCs) are a group of electroactive polymer materials that exhibit a large deformation due to the application of low voltages resulting from the movement of cations inside the polymer. These materials have many applications in various fields such as Micro-robotics, biomedical engineering equipment and artificial muscles. Due to the possibility of producing these materials in micro dimensions they can also be used in micro-electromechanical systems. On the other hand, due to their sensitivity to very low voltages, they can be a good substitute for silicon in micro-electromechanical systems. In the present study, the dynamical analysis of a micro-beam fixed at two ends made of these materials is investigated using electrical-chemical-mechanical relations. COMSOL Multiphysics software is used to solve the relations. The results showed that for harmonic stimulation (sinusoidal voltage) the system experiences only the same form of the first mode. It was also observed that increasing the frequency would decrease the amplitude of the micro-beam oscillation.
| DOI | 10.11648/j.cbe.20200501.13 |
| Published in | Chemical and Biomolecular Engineering (Volume 5, Issue 1, March 2020) |
| Page(s) | 15-20 |
| Creative Commons |
This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited. |
| Copyright |
Copyright © The Author(s), 2024. Published by Science Publishing Group |
Ionic Polymer Metal Composites, Micro-beam, Physical Model, COMSOL Multiphysics, Micro-electromechanical Systems
| [1] | Ghadimi, A., & Asadi, S. (2018). Modelling of composite right/left‐handed active multiconductor transmission lines (AMCTL) in time domain. International Journal of Numerical Modelling: Electronic Networks, Devices and Fields, 31 (1), e2257 |
| [2] | Chegeni, M., Pour, S. K., & Dizaji, B. F. (2019). Synthesis and characterization of novel antibacterial Sol-gel derived TiO2/Zn2 TiO4/Ag nanocomposite as an active agent in Sunscreens. Ceramics International, 45 (18), 24413–24418. doi: 10.1016/j.ceramint.2019.08.163 |
| [3] | Shahinpoor, M., & Kim, K. J. (2001). Ionic polymer-metal composites: I. Fundamentals. Smart materials and structures, 10 (4), 819. |
| [4] | Nemat-Nasser, S., & Li, J. Y. (2000). Electromechanical response of ionic polymer-metal composites. Journal of Applied Physics, 87 (7), 3321-3331. |
| [5] | Del Bakhshayesh, A. R., Asadi, N., Alihemmati, A., Nasrabadi, H. T., Montaseri, A., Davaran, S.,... & Abedelahi, A. (2019). An overview of advanced biocompatible and biomimetic materials for creation of replacement structures in the musculoskeletal systems: focusing on cartilage tissue engineering. Journal of biological engineering, 13 (1), 85. |
| [6] | Hosseini, V., Maroufi, N. F., Saghati, S., Asadi, N., Darabi, M., Ahmad, S. N. S.,... & Rahbarghazi, R. (2019). Current progress in hepatic tissue regeneration by tissue engineering. Journal of translational medicine, 17 (1), 383. |
| [7] | Shahinpoor, M. and Kim, K. J.. 2001. "Ionic polymer-metal composites: I. Fundamentals". Smart materials and structures, 10 (4), Aug, pp. 819. |
| [8] | Kim, K. J. and Shahinpoor. M., 2002. "A novel method of tnanufixturing three-dimensional ionic polymer—metal composites (IPMCs) biomitnetic sensors. actuators and artificial muscles". Polymer, 43 (3), Feb, pp. 797-802. |
| [9] | Kim, K. J. and Shahinpoor, M., 2003. "Ionic polymer—metal composites: II. Manufacturing techniques". Smart materials and structures, 12 (1), Jan, pp. 65. |
| [10] | Punning, A., Kruusmaa, M. and Aabloo, A., 2007. "A self-sensing ion conducting polymer metal composite (IPMC) actuator". Sensors and Achialors A: Physical, 136 (2), May. pp. 656-664. |
| [11] | Moeinkhah, H., Reneepazhand, J, and Akbarzadeh, A., 2013. "Analytical dynamic modeling of a cantilever IPMC actuator based on a distributed electrical circuit". Smart Materials and Structures, 22 (5), Apr, pp. 055033. |
| [12] | Annabestani, M. and Naghavi, N., 2014. "Nonlinear identification of PMC actuators based on ANFIS—NARX paradigm". Sensors and Actuators A: Physical, 209 (1), Mar, pp. 140-148. |
| [13] | Caponetto, R., Graziani, S., Pappalardo, F. and Sapuppo, F., 2014. "Identification of IPMC nonlinear model via single and multi-objective optimization algorithms". ISA transactions, 53 (2), Mar, pp. 481-488. |
| [14] | Hu, Y. J., Yang, J. and Kitipornchai, S., 2013. "Snap-through and pull-in analysis of an clectro-dynamically actuated curved micro-beam using a nonlinear beam model". Journal of Sound and Vibration, 332 (15), Jul, pp. 3821-3832. |
| [15] | Hsu, T. R., 2008. MEMS and Microsystems: Design, iidangfacture, and Nanoscale Engineering, John Wiley & Sons, New Jersey. |
| [16] | Chen, Z., 2009. "Ionic polymer-metal composite artificial muscles and sensors: A control systems perspective". PhD Thesis, Michigan State University. Michigan. |
| [17] | Esmaeili, S., Nasiri, M., Dadashi, N., & Safari, H. (2016). Wave function properties of a single and a system of magnetic flux tube (s) oscillations. Journal of Geophysical Research: Space Physics, 121 (10), 9340-9355. |
| [18] | Mohammadzadeh, A., Ghoddoosian, A., & Noori-Damghani, M. (2011). Balancing of the flexible rotors with particle swarm optimization method. International Review of Mechanical Engineering, 5 (3), 490-496. |
| [19] | Damghani, Mohammad Nouri, and Arash Mohammadzadeh Gonabadi. “Numerical Study of Energy Absorption in Aluminum Foam Sandwich Panel Structures Using Drop Hammer Test.” Journal of Sandwich Structures & Materials, vol. 21, no. 1, Jan. 2019, pp. 3–18, doi: 10.1177/1099636216685315. |
| [20] | Afshar, A., Hosseini, M. S., & Behzadfar, E. (2014). Numerical study of the agglomerates dispersion behavior in shear and elongational flow fields in viscous media using Population Balance Modeling (PBM). Scientia Iranica. Transaction C, Chemistry, Chemical Engineering, 21 (6), 2107. |
| [21] | Thompson, D. S., Meng, D., Afshar, A., Bassou, R., Zong, J., Bonaccurso, E.,... & Vercillo, V. (2018). Initial Development of a Model to Predict Impact Ice Adhesion Stress. In 2018 Atmospheric and Space Environments Conference (p. 3344). |
| [22] | Azarang, A., Kamaei, S., Miri, M., & Asemani, M. H. (2016). A new fractional-order chaotic system and its synchronization via Lyapunov and improved Laplacian-based method. Optik, 127 (24), 11717-11731. |
| [23] | Azarang, A., Ranjbar, J., Mohseni, H., & Andy, M. A. (2017). Output feedback synchronization of a novel chaotic system and its application in secure communication. International Journal of Computer Science and Network Security, 17, 72-77. |
| [24] | Azarang, A., Miri, M., Kamaei, S., & Asemani, M. H. (2018). Nonfragile fuzzy output feedback synchronization of a new chaotic system: design and implementation. Journal of Computational and Nonlinear Dynamics, 13 (1), 011008. |
| [25] | Ramtin, A., Hakami, V., & Dehghan, M. (2013, December). A Perturbation-Proof Self-stabilizing Algorithm for Constructing Virtual Backbones in Wireless Ad-Hoc Networks. In International Symposium on Computer. Networks and Distributed Systems (pp. 66-76). Springer, Cham |
| [26] | Ramtin, A., Hakami, V., & Dehghan, M. (2014, September). A self-stabilizing clustering algorithm with fault-containment feature for wireless sensor networks. In 7'th International Symposium on Telecommunications (IST'2014) (pp. 735-739). IEEE. |
| [27] | Ramtin, A., Hakami, V., & Dehghan, M. (2014, May). Self-stabilizing algorithms of constructing virtual backbone in selfish wireless ad-hoc networks. In 2014 22nd Iranian Conference on Electrical Engineering (ICEE) (pp. 914- 919). IEEE. |
| [28] | Zareanshahraki, F., & Mannari, V. (2018). “Green” UV‐LED gel nail polishes from bio‐based materials. International journal of cosmetic science, 40 (6), 555-564. |
| [29] | Karami, Z., Kabiri, K., & Zohuriaan-Mehr, M. J. (2019). Non-isocyanate polyurethane thermoset based on a bio-resourced star-shaped epoxy macromonomer in comparison with a cyclocarbonate fossil-based epoxy resin: A preliminary study on thermo-mechanical and antibacterial properties. Journal of CO2 Utilization, 34, 558-567. |
| [30] | Ghasemlou, M., Daver, F., Ivanova, E. P., & Adhikari, B. (2020). Synthesis of green hybrid materials using starch and non-isocyanate polyurethanes. Carbohydrate Polymers, 229, 115535. |
| [31] | Akdogan, O. K., Zareanshahraki, F., & Mannari, V. (2019). Dual-cure polyurethane coatings from soybean oil and their film properties as a function of cure sequence. Eur. J. Lipid Sci. Technol., 50 (4), 112-122. |
| [32] | Khiabani, A. G., & Heydari, A. (2019). Design and implementation of an optimal switching controller for uninterruptible powersupply inverters using adaptive dynamic programming. IET Power Electronics |
| [33] | Khiabani, A. G., & Heydari, A. (2018, September). Optimal switching of voltage source inverters using approximate dynamic programming. In ASME 2018 Dynamic Systems and Control Conference (pp. V001T01A006-V001T01A006). American Society of Mechanical Engineers. |
| [34] | Babazadeh, R., & Khiabani, A. G. (2018, October). Nonlinear Observer Design for RC Battery Model for Estimating State of Charge & State of Health Based on State-Dependent Riccati Equation. In 2018 IEEE Electrical Power and Energy Conference (EPEC) (pp. 1-5). IEEE. |
| [35] | Razzaghi, P., Al Khatib, E., & Bakhtiari, S. (2019). Sliding mode and SDRE control laws on a tethered satellite system to de-orbit space debris. Advances in Space Research, 64 (1), 18-27. |
| [36] | Razzaghi, P., Al Khatib, E., & Hurmuzlu, Y. (2019). Nonlinear dynamics and control of an inertially actuated jumper robot. Nonlinear Dynamics, 1-16. |
| [37] | Hayati, H., & Ehsanian, M. (2014, December). Low-power burst-mode clock recovery circuit using analog phase interpolator. In 2014 26th International Conference on Microelectronics (ICM) (pp. 120-123). IEEE. |
| [38] | Hayati, H., & Ehsanian, M. (2015). A 5-Gbps CMOS Burst-Mode CDR Circuit With an Analog Phase Interpolator for PONs. Informacije MIDEM, 45 (1), 39-46. |
| [39] | Avval, A. G., & El-Ghazaly, S. M. (2018, April). Holistic optimization technique for solving low thermal conductivity of sapphire substrates in high frequency devices. In 2018 Texas Symposium on Wireless and Microwave Circuits and Systems (WMCS) (pp. 1-4). IEEE. |
| [40] | A. G. Avval, E. Larique, S. M. El-Ghazaly, "Heterojunction field effect transistors" in Reference Module in Materials Science and Materials Engineering, Elsevier, 2018. |
| [41] | Ghayouraneh, S., El-Ghazaly, S. M., & Rankin, J. M. (2018). Dynamic Addressing for On-Demand Mobility. In 2018 Aviation Technology, Integration, and Operations Conference (p. 4152). |
| [42] | Ghayouraneh, S., Rankin, J. M., & El-Ghazaly, S. M. (2019). Practical Considerations in Traffic Flow Systems for ODM Vehicles. In 2019 Integrated Communications, Navigation and Surveillance Conference (ICNS) (pp. 1-7). IEEE. |
| [43] | Ghayouraneh, S., El-Ghazaly, S., & Rankin, J. (2019). Investigation of Traffic Flow for ODM Vehicles in Dynamic ICAO Addressing Process. In AIAA Aviation 2019 Forum (p. 3627). |
| [44] | Gharib, M. R., & Daneshvar, A. (2019). Quantitative-fuzzy Controller Design for Multivariable Systems with Uncertainty. International Journal of Control, Automation and Systems, 17 (6), 1515-1523. |
| [45] | Kondori, A., Esmaeilirad, M., Baskin, A., Song, B., Wei, J., Chen, W.,... & Asadi, M. (2019). Identifying Catalytic Active Sites of Trimolybdenum Phosphide (Mo3P) for Electrochemical Hydrogen Evolution. Advanced Energy Materials, 9 (22), 1900516. |
| [46] | Ranjbar O. A., A. N. Volkov, Kinetic and hydrodynamic simulations of laser-induced plume expansion, Early Career Tech. J. 15 (2016) 160–167 |
| [47] | Ranjbar, O. A., Lin, Z., & Volkov, A. N. (2018). One dimensional kinetic simulations of plume expansion induced by multi-pulse laser irradiation in the burst mode at 266 nm wavelength. Vacuum, 157, 361-375 |
| [48] | Palya, A., Ranjbar, O. A., Lin, Z., & Volkov, A. N. (2018). Effect of the background gas pressure on the effectiveness of laser-induced material removal from deep cavities in irradiated targets. Applied Physics A, 124 (1), 32. |
| [49] | Hemmati, R., & Rahideh, A. (2017). Optimal design of slotless tubular linear brushless PM machines using metaheuristic optimization techniques. Journal of Intelligent & Fuzzy Systems, 32 (1), 351-362. |
| [50] | Hemmati, R., Wu, F., & El-Refaie, A. (2019, May). Survey of Insulation Systems in Electrical Machines. In 2019 IEEE International Electric Machines & Drives Conference (IEMDC) (pp. 2069-2076). IEEE. |
| [51] | Nikoobakht, A., Aghaei, J., Fallahzadeh-Abarghouei, H., & Hemmati, R. (2019). Flexible Co-Scheduling of Integrated Electrical and Gas Energy Networks under Continuous and Discrete Uncertainties. Energy. |
| [52] | Tehrani, M., Moshaei, M. H., & Sarvestani, A. S. (2017). Network polydispersity and deformation‐induced damage in filled elastomers. Macromolecular Theory and Simulations, 26 (6), 1700038 |
| [53] | Moshaei, M. H., Tehrani, M., & Sarvestani, A. (2019). On stability of specific adhesion of particles to membranes in simple shear flow. Journal of biomechanical engineering, 141 (1), 011005. |
| [54] | Moshaei, M. H., Tehrani, M., & Sarvestani, A. (2019). Rolling adhesion of leukocytes on soft substrates: Does substrate stiffness matter?. Journal of biomechanics |
| [55] | Moghaddam, H., Hajirasouliha, I., & Doostan, A. (2005). Optimum seismic design of concentrically braced steel frames: concepts and design procedures. Journal of Constructional Steel Research, 61 (2), 151-166. |
| [56] | Moghaddam, H., & Hajirasouliha, I. (2009). On the optimum performance-based design of structures. In Proceedings of a US-Iran Seismic Workshop, Irvine, California, PEER report (Vol. 2). |
| [57] | Movahedi, N., Linul, E., & Marsavina, L. (2018). The temperature effect on the compressive behavior of closed-cell aluminum-alloy foams. Journal of Materials Engineering and Performance, 27 (1), 99-108. |
| [58] | Movahedi, N., Taherishargh, M., Belova, I. V., Murch, G. E., & Fiedler, T. (2019). Mechanical and Microstructural Characterization of an AZ91–Activated Carbon Syntactic Foam. Materials, 12 (1), 3. |
| [59] | Ahmadzadegan, M. H., KINNUNEN, M., & Fabritius, T. (2014). Ant colony optimization approach to digital comparative holography through traveling salesman problem. Optoelectronics and Advanced Materials-Rapid Communications, 8 (November-December 2014), 1246- 1249. |
| [60] | Ahmadzadegan, M. H., & Fabritius, T. (2013, August). Kiyotaki-Moore approach to wavefront manipulation in digital comparative holography. In 2013 3rd International Conference on Instrumentation Control and Automation (ICA) (pp. 203-206). IEEE |
| [61] | Ahmadzadegan, M. H., Fabritius, T., & Notare, M. S. M. A. (2014). Chaotic analysis of optical vignetting in digital comparative holography. IEEE Latin America Transactions, 12 (2), 244-247. |
| [62] | Ahmadzadegan, M. H., & Fabritius, T. (2014, October). Percolation approach to digital comparative holography via optical flow investigation. In 2014 4th International Conference on Computer and Knowledge Engineering (ICCKE) (pp. 200-203). IEEE. |
| [63] | Pugal, D., Kim, K. J. and Aabloo, A., 2011. "An explicit physics-based model of ionic polymer-metal composite actuators". Journal ofApplied Physics. Oct, 110 (8), pp. 084904 |
| [64] | Pugal, D., 2012. Physics based model of ionic polymer-metal composite electromechanical and mechanoelectrical transduction. PhD Thesis, University of Nevada, Reno. |
| [65] | Shen, Q., Palmre, V., Stalbaum, T., & Kim, K. J. (2015). A comprehensive physics-based model encompassing variable surface resistance and underlying physics of ionic polymer-metal composite actuators. Journal of Applied Physics, 118 (12), 124904. |
APA Style
Mohammad Reza Salehi Kolahi, Hossein Moinekhah. (2020). Analysis and Study of the Nonlinear Electrodynamics Behaviour of a Micro-beam Made of Ionic Polymer Metal Composite (IPMC). Chemical and Biomolecular Engineering, 5(1), 15-20. https://doi.org/10.11648/j.cbe.20200501.13
ACS Style
Mohammad Reza Salehi Kolahi; Hossein Moinekhah. Analysis and Study of the Nonlinear Electrodynamics Behaviour of a Micro-beam Made of Ionic Polymer Metal Composite (IPMC). Chem. Biomol. Eng. 2020, 5(1), 15-20. doi: 10.11648/j.cbe.20200501.13
AMA Style
Mohammad Reza Salehi Kolahi, Hossein Moinekhah. Analysis and Study of the Nonlinear Electrodynamics Behaviour of a Micro-beam Made of Ionic Polymer Metal Composite (IPMC). Chem Biomol Eng. 2020;5(1):15-20. doi: 10.11648/j.cbe.20200501.13
Share This Article
Twitter
Linked In
Facebook
Copy
Download@article{10.11648/j.cbe.20200501.13,
author = {Mohammad Reza Salehi Kolahi and Hossein Moinekhah},
title = {Analysis and Study of the Nonlinear Electrodynamics Behaviour of a Micro-beam Made of Ionic Polymer Metal Composite (IPMC)},
journal = {Chemical and Biomolecular Engineering},
volume = {5},
number = {1},
pages = {15-20},
doi = {10.11648/j.cbe.20200501.13},
url = {https://doi.org/10.11648/j.cbe.20200501.13},
eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.cbe.20200501.13},
abstract = {Ionic Polymer Metal Composites (IPMCs) are a group of electroactive polymer materials that exhibit a large deformation due to the application of low voltages resulting from the movement of cations inside the polymer. These materials have many applications in various fields such as Micro-robotics, biomedical engineering equipment and artificial muscles. Due to the possibility of producing these materials in micro dimensions they can also be used in micro-electromechanical systems. On the other hand, due to their sensitivity to very low voltages, they can be a good substitute for silicon in micro-electromechanical systems. In the present study, the dynamical analysis of a micro-beam fixed at two ends made of these materials is investigated using electrical-chemical-mechanical relations. COMSOL Multiphysics software is used to solve the relations. The results showed that for harmonic stimulation (sinusoidal voltage) the system experiences only the same form of the first mode. It was also observed that increasing the frequency would decrease the amplitude of the micro-beam oscillation.},
year = {2020}
}
TY - JOUR T1 - Analysis and Study of the Nonlinear Electrodynamics Behaviour of a Micro-beam Made of Ionic Polymer Metal Composite (IPMC) AU - Mohammad Reza Salehi Kolahi AU - Hossein Moinekhah Y1 - 2020/01/17 PY - 2020 N1 - https://doi.org/10.11648/j.cbe.20200501.13 DO - 10.11648/j.cbe.20200501.13 T2 - Chemical and Biomolecular Engineering JF - Chemical and Biomolecular Engineering JO - Chemical and Biomolecular Engineering SP - 15 EP - 20 PB - Science Publishing Group SN - 2578-8884 UR - https://doi.org/10.11648/j.cbe.20200501.13 AB - Ionic Polymer Metal Composites (IPMCs) are a group of electroactive polymer materials that exhibit a large deformation due to the application of low voltages resulting from the movement of cations inside the polymer. These materials have many applications in various fields such as Micro-robotics, biomedical engineering equipment and artificial muscles. Due to the possibility of producing these materials in micro dimensions they can also be used in micro-electromechanical systems. On the other hand, due to their sensitivity to very low voltages, they can be a good substitute for silicon in micro-electromechanical systems. In the present study, the dynamical analysis of a micro-beam fixed at two ends made of these materials is investigated using electrical-chemical-mechanical relations. COMSOL Multiphysics software is used to solve the relations. The results showed that for harmonic stimulation (sinusoidal voltage) the system experiences only the same form of the first mode. It was also observed that increasing the frequency would decrease the amplitude of the micro-beam oscillation. VL - 5 IS - 1 ER -
Information
Email: